Switching Concepts, Cabling & Interface Issues
CCNA 200-301 · Network Fundamentals
Switching is the foundation skill of the CCNA: if you cannot explain what a switch does with a frame, VLANs, spanning tree, and EtherChannel will all feel mysterious, because each of them is switching with extra rules. The good news is that the core behaviour is simple, and the exam tests it the same way every time — by asking what a switch does when the destination is known, unknown, or a broadcast, and by asking you to diagnose the small physical problems that break links.
How a switch learns and forwards
A switch forwards Ethernet frames using a MAC address table (also called the CAM table). When a frame arrives, the switch reads its source MAC address and records which port that address lives on — this is MAC learning. Entries do not last forever: each one has an aging timer (300 seconds by default on Cisco switches), and if no frame arrives from that address before the timer expires, the entry is removed. This MAC aging is what lets the table stay correct when devices move or are replaced.
With the source learned, the switch looks up the destination MAC address. If the destination is in the table, the switch forwards the frame out of that one port only — this is frame switching (unicast forwarding), and it is what makes a switch better than a hub: each conversation gets its own dedicated path instead of everyone hearing everything. If the destination is not in the table, the switch floods the frame out of all ports except the one it arrived on. Flooding is normal and necessary — it is how the switch finds a device it has not learned yet. The reply from that device teaches the switch its location, so the next frame goes directly. Broadcast frames (destination MAC ff:ff:ff:ff:ff:ff) and unknown multicast frames are also flooded, by design.
Two consequences matter for the exam. First, a switch forwards broadcasts, so all devices in a VLAN share one broadcast domain — only a router breaks that up. Second, a switch starts with an empty MAC table when it boots, so its first frames are flooded; a question that asks what a switch does with a frame to an unknown destination always has the same answer: flood it. You can inspect the table with show mac address-table and clear it with clear mac address-table dynamic.
Cabling and physical interfaces
Copper cabling (twisted pair, such as Cat5e/Cat6/Cat6a) is the standard for short runs: up to 100 metres for Ethernet, inexpensive, and able to carry PoE. Multimode fiber uses a wider core that carries light over shorter distances — typically up to a few hundred metres — and is common inside buildings and campuses. Single-mode fiber uses a narrow core with a single path of light, which travels much further (kilometres to tens of kilometres) and is used for long-distance and service-provider links. The exam's comparison is straightforward: copper is cheap and short, multimode is medium distance, single-mode is long distance. Fiber also has a practical advantage the exam likes: it is immune to electromagnetic interference, so it is the right choice near heavy electrical equipment.
Connections can be point-to-point — two devices directly linked, the normal case for a switch-to-switch or switch-to-router link — or shared media, where several devices share one collision domain, as with a hub or old coaxial Ethernet. Modern switched networks are point-to-point everywhere, which is why collisions are largely a historical topic — but the exam still tests them, because recognising a collision problem is part of diagnosing interface issues.
Interface and cable issues
When a link misbehaves, show interfaces is your first command, and the exam expects you to read its output. Collisions happen when two devices transmit at the same time on shared media; in a modern full-duplex switched network you should see essentially none, so a rising collision count points to a hub in the path or a duplex problem. A duplex mismatch — one side set to full duplex and the other to half duplex — is a classic exam scenario: the half-duplex side sees collisions and late collisions, the link appears to work but performs terribly, and the fix is to match the settings (usually by leaving both sides on autonegotiation). A speed mismatch is simpler and harsher: the link usually does not come up at all, or comes up and immediately drops, because the two sides cannot agree on a signalling rate.
Errors in the interface counters tell their own stories. CRC errors and input errors often point to a damaged cable, a bad connector, or electrical interference. Runts (frames smaller than 64 bytes) and giants (frames larger than the maximum) suggest a faulty network interface card or a duplex problem. A steadily increasing error count on one interface, while the neighbour's counters stay clean, usually means the problem is the cable or the local port — swap the cable first, because it is the cheapest fix and the most common fault.
One more distinction the exam tests: the difference between a port being administratively down (shut down with the shutdown command — show interfaces reports "administratively down") and a port that is up at Layer 1 but down at Layer 2. If the status is up but the line protocol is down, the physical link works but something above it — encapsulation, keepalives, or a duplex problem — is failing. Reading that first line of show interfaces output is a small skill that answers a surprising number of exam questions.
Putting it together: reading show interfaces output
When a question shows you show interfaces output, read it in a fixed order. First, the status line: up/up means the link is healthy at Layers 1 and 2; administratively down means someone shut the port down; up with the line protocol down means a Layer 2 problem. Second, the speed and duplex lines: confirm they match the neighbour, because a mismatch is the single most common cause of a link that is up but slow. Third, the error counters: CRC errors and input errors point at the cable or the physical layer, while collisions and late collisions point at a duplex problem. Fourth, the five-minute input and output rates, which tell you whether the link is actually carrying traffic or merely up. Practise this reading order in Packet Tracer until it is automatic: build a link, break it deliberately (set a duplex mismatch, shut a port down, unplug a cable), and read the output each time. The exam rewards candidates who can move from symptom to cause in one step, and that skill comes from seeing the counters change, not from memorising their definitions.
Exam traps to watch for
- Saying a switch drops a frame with an unknown destination MAC. It floods it out of all ports except the receiving port — dropping would break learning.
- Confusing single-mode and multimode fiber: single-mode goes further (kilometres), multimode is for shorter in-building runs.
- Blaming collisions for a problem on a modern full-duplex link. Collisions belong to half-duplex/shared media; on a full-duplex switched link, suspect a duplex mismatch instead.
- Forgetting that a switch forwards broadcasts. Only a router separates broadcast domains.
Practice questions
Test yourself on this guide. Answers are checked instantly, with a full explanation for each question.
Q1.A switch receives a unicast frame whose destination MAC address is not in its MAC address table. What does the switch do with the frame?
Explanation: When the destination MAC address is unknown, the switch floods the frame out of all ports except the receiving port, so the frame can still reach its destination — and the destination's reply then teaches the switch its location. Option B is wrong because dropping unknown unicast frames would prevent communication with any device the switch has not yet learned. Option C is wrong because switches do not know about default gateways; that is a host and router concept. Option D is wrong because switches do not send ARP requests to resolve unknown MAC addresses; ARP is used by hosts and routers to map IP addresses to MAC addresses.
Exam objective: 200-301 1.13: Switching concepts — frame flooding and MAC address table
Q2.A switch learns a MAC address from the source address of an incoming frame. After how long is that entry removed if no further frames arrive from that address?
Explanation: MAC address table entries age out after the aging timer expires — 300 seconds (5 minutes) by default on Cisco switches — if no frame from that source MAC address refreshes them. Option A is wrong because learning persists after forwarding; that is the whole point of the table. Option C is wrong because dynamic entries are not permanent; only statically configured entries stay indefinitely. Option D is wrong because 30 seconds is not the MAC aging default, and ARP timeouts are a separate mechanism on hosts and routers.
Exam objective: 200-301 1.13: Switching concepts — MAC learning and aging
Q3.An engineer needs to connect two buildings 8 kilometres apart with a single link. Which media type is the correct choice?
Explanation: Single-mode fiber uses a narrow core with a single light path, supporting links of many kilometres, which is what an 8 km inter-building link needs. Option A is wrong because copper Ethernet is limited to about 100 metres. Option B is wrong because multimode fiber is limited to a few hundred metres — far too short for 8 km. Option D is wrong because coaxial cable is an obsolete Ethernet medium with short distance limits, and it is not immune to interference in the way fiber is.
Exam objective: 200-301 1.3: Compare physical interface and cabling types — single-mode fiber, multimode fiber, copper
Q4.A link between a switch and a server is up but extremely slow. show interfaces shows a large and growing number of late collisions on the switch port. What is the most likely cause?
Explanation: Late collisions on a link that is up but performing badly are the classic symptom of a duplex mismatch: the half-duplex side detects collisions while the full-duplex side transmits whenever it wants, so throughput collapses. Option A is wrong because an over-length cable typically causes CRC errors or a link that will not come up, not late collisions. Option B is wrong because a speed mismatch normally prevents the link from coming up at all. Option D is wrong because a full MAC table causes flooding of unknown unicast frames, not collisions.
Exam objective: 200-301 1.4: Identify interface and cable issues — mismatch duplex
Q5.Which command displays the contents of a switch's MAC address table?
Explanation: show mac address-table displays the switch's learned MAC addresses, the ports they were learned on, and the VLANs they belong to. Option A is wrong because show ip route displays the routing table, which is a router (or Layer 3 switch) function. Option B is wrong because show running-config displays the device's current configuration, not the dynamic MAC table. Option C is wrong because show interfaces status shows port state, speed, duplex, and VLAN — not learned MAC addresses.
Exam objective: 200-301 1.13: Switching concepts — MAC address table
Q6.A broadcast frame arrives at a switch. How does the switch handle it?
Explanation: Switches flood broadcast frames (destination MAC ff:ff:ff:ff:ff:ff) out of all ports in the same VLAN except the port the frame arrived on — that is how ARP requests and DHCP discovers reach their targets. Option B is wrong because it is routers, not switches, that block broadcasts. Option C is wrong because a switch does not single out a router port for broadcasts; it floods them to the whole VLAN. Option D is wrong because a switch never rewrites a broadcast destination into a unicast address.
Exam objective: 200-301 1.13: Switching concepts — frame flooding
Q7.An interface shows 'up, line protocol is down' in show interfaces output. What does this indicate?
Explanation: Status 'up' means Layer 1 is working (a signal is present), while 'line protocol is down' means Layer 2 is failing — typically an encapsulation mismatch, a keepalive problem, or a duplex issue. Option A is wrong because a shut-down port shows 'administratively down', not 'up'. Option C is wrong because with no cable the interface would show 'down, line protocol is down'. Option D is wrong because a missing IP address does not affect the line protocol state of an interface.
Exam objective: 200-301 1.4: Identify interface and cable issues
Q8.Why is fiber-optic cabling preferred over copper in an industrial area with heavy electrical machinery?
Explanation: Fiber carries data as light rather than electrical signals, so electromagnetic interference from motors and heavy machinery cannot corrupt the signal — a major advantage in industrial environments. Option A is backwards: copper carries PoE, fiber cannot carry electrical power. Option C is wrong because fiber is generally more expensive to buy and install than copper. Option D is wrong because fiber does not change collision-domain behaviour; modern switched networks have no shared collision domains either way.
Exam objective: 200-301 1.3: Compare physical interface and cabling types — single-mode fiber, multimode fiber, copper
Q9.Two switches are connected by a single Ethernet cable, with no other devices on the link. What type of connection is this?
Explanation: A link between exactly two devices is a point-to-point connection — the normal case for switch-to-switch links in a modern network, and it has no collisions because only two devices share the link. Option B is wrong because shared media means several devices share one medium, as with a hub. Option C is wrong because a broadcast domain is a logical concept (the set of devices that receive each other's broadcasts), not a description of a physical connection. Option D is wrong because with only two devices in full-duplex mode there is effectively no collision domain to worry about.
Exam objective: 200-301 1.3: Compare physical interface and cabling types — Ethernet shared media and point-to-point